Remove loose surface contaminants ... road film, dirt, grease and grime, salt, insect remains and bird droppings. Wash (by hand) weekly or fortnightly with luke-warm water, using a high quality lambswool or sheepskin wash mitt (on paintwork) and microfibre wash mitt (wheels), employing the two-bucket wash method. Rinse off suds / foam thoroughly with a garden hose or pressure washer. Pat dry afterwards with a soft microfibre drying towel to avoid water spotting.

Mild / pH Balanced Wash Shampoo - Remove dirt, road film, insect remains, bird droppings, airborne pollutants and other grime, without removing sealant protection.

pH Neutral Snow Foam - Optional prewash foaming solution (thick clinging foam) to remove heavier dirt and grime (touchless wash), before the main washing process.

APC (All Purpose Cleaner) - Optional prewash to remove stubborn road grime, grease, dried on insect remains and old preservative coatings.

Remove bonded surface contaminants ... tar spots, bug splatter, tree sap, brake and rail dust, industrial and environmental fallout, exhaust soot and paint overspray.

a) Tar Remover - Remove tar, bug splatter, adhesives, grease and oil stains.

b) Fallout Remover - Remove brake and rail dust, industrial fallout (iron particles).

c) Detailing Clay - Remove tree sap mist, airborne environmental deposits and paint overspray.

Remove or reduce the appearance of paint defects ... scratches, swirl marks, water-spot etching, holograms and oxidation. Restore colour intensity. Maximise surface gloss and finish clarity.

Cleanser and Sealant All-In-One (Gentle Cleaner Sealant) - Remove microscopic dirt particles and other contaminants. Clean and brighten lightly oxidised paintwork or fibreglass gel coat, without the use of abrasives.

OR

Hologram Remover Polish - For a high gloss, hologram free finish (especially on darker colours).

High Gloss Polish (Light Cut or Finishing Polish) - Remove light swirl marks, oxidation and fine scratches. Gloss enhancer.

Swirl Remover (Medium Cut or Intensive Polish) - Remove swirl marks, oxidation and scratches. Colour restorer.

Scratch Remover (Heavy Duty Compound) - Remove deeper scratches.

Seal and protect against the elements ... UV radiation, acid rain, environmental and industrial pollution, hard water spots, road salts, insect remains, bug splatter and bird droppings.

Sealant Polish or Paint Sealant - Long lasting protection against contamination, corrosion and the sun's ultraviolet rays. A premium quality nano sealant will leave behind a high-gloss (glass-like), super-slick, non-stick finish.

Keep that just detailed look ... Remove fresh contaminants, boost sealant protection, enhance surface gloss and slickness. Use after every wash to remove water spots or as a drying aid.

Sealant Spray - Fortify / extend the lifespan of the existing sealant coating. Increase protection from harmful UV rays, dirt and staining.

Restructure (and Crystal Diamond Glaze) compounds, polishes and sealants are among the best performing and user-friendly products on the market. Fantastic results are easily achievable when employing a methodical approach, having good technique, showing meticulous attention to detail. Restructure products are very forgiving. They cannot be over applied, nor require application with precision timing. As the products get fully absorbed into the finish, excess residues are minimal and wipe off very easily. In fact, Restructure products are applied (and topped up) with more simplicity than most other polish and sealant (paint protection) systems. They can even be used as one-step products, much like an over-the-counter sealant polish protectant. Therefore are perfectly suitable for use by relative beginners and hobbyists (detailing enthusiasts), not solely professional detailers.

Oxidation remover / surface cleanser, colour restorer, gloss enhancer; Blemish and light scratch remover (filler). Suitable for nearly-new and dull (lightly to moderately oxidised) paint / gel coat / surface conditions. Micro Finishing Compound is an excellent preparatory product (pre-cleaner), before the application of Re-Structure or Crystal Diamond Glaze Polish (Sealant).

Directions: Wash and dry vehicle / aircraft / watercraft thoroughly, before applying Micro Finishing Compound. This particular compound should be followed up with application(s) of RMP Marine or CDG Auto / Aviation Sealant Polish. These products should be used exclusively, as they are not suitable for mixing with other manufacturers wax or polymer based products.

Always work in the shade or out of direct sunlight (strong sunshine). It is best to apply the compound when surface is cool to the touch, otherwise the product may dry out too quickly, making application more difficult. Ideally, work indoors, in a cool, dry environment with good lighting and ventilation. Avoid contact with porous plastic and rubber trim. If you get any compound on same, just wipe it off there and then.

Shake well before use. Re-Structure or Crystal Diamond Glaze Micro Finishing Compound should be applied to a cool, clean, dry surface only.

Hand Application: Do not dampen your applicator pad before use. The pad should only be damp with product (not water) during application. Place a pea sized amount of compound (no more) on a soft foam applicator pad (the softer black side of our special tri-foam applicators). Work on a 1 ft x 1 ft area at a time. This will ensure the product does not dry out before you work it fully into the finish. Using light to moderate pressure, rub briskly in a circular motion. Apply sufficient pressure initially, to remove microscopic dirt particles and oxidation. Continue rubbing in compound until it disappears (gets absorbed ... more readily when using gentle pressure) and a high-gloss shine is visible. Wipe off any excess product (compound residue) carefully as you go, with a soft microfibre buffing cloth. Move to another section and repeat the application process, using a pea sized amount of compound for every square foot of surface area. Finish one panel or area entirely (apply product and buff off any excess) before moving on to the next section.

Machine Application: RMP or CDG Micro Finishing Compound (non-abrasive) may also be applied by dual-action polisher, fitted with a foam polishing pad. Use small amounts of compound and work on a 2 ft x 2 ft area at a time. Allow the machine to operate under its own weight, without exerting much downward pressure. Work the compound into the finish at low to moderate speeds only (using slow overlapping passes), until it disappears and a high-gloss shine is visible. Wipe off any excess product (compound residue) carefully as you go, with a soft microfibre buffing cloth. Move to another section and repeat the process.

Follow-up by applying Re-Structure or Crystal Diamond Glaze Polish (Sealant) for long-lasting protection.

Last step product or one-step polish / protectant (nano-technology sealant). Suitable for marine, aviation and automotive paints; fibreglass gel coat, glass, plexiglass, polycarbonate, non-porous (hard / smooth) plastics, carbon fibre, varnished woods, brass, chrome, stainless steel, polished aluminium, alloy wheels, propeller / rotor blades and deicing boots.

Apply to new, nearly-new or restored surfaces only (i.e. clean, uncontaminated, oxidation-free and wax-free). For contaminated or oxidised surfaces, clean and restore the finish with RMP or CDG Micro-Finishing Compound (as a preparatory treatment), before following-up with an application of Re-Structure or Crystal Diamond Glaze Polish (Sealant).

Directions: Wash and dry vehicle / aircraft / watercraft thoroughly, before applying RMP or CDG Polish. These products should be used exclusively, as they are not suitable for mixing with other manufacturers wax or polymer based products.

Always work in the shade or out of direct sunlight (strong sunshine). It is best to apply the polish when surface is cool to the touch, otherwise the product may dry out too quickly, making application more difficult. Ideally, work indoors, in a cool, dry environment with good lighting and ventilation. It also prevents the sealant coating from getting wet while it cures. Avoid contact with porous plastic and rubber trim. If you get any polish on same, just wipe it off there and then.

Shake well before use. Re-Structure or Crystal Diamond Glaze Polish should be applied to a cool, clean, dry surface only.

Hand Application: Do not dampen your applicator pad before use. The pad should only be damp with product (not water) during application. Place a pea sized amount of polish (no more) on a soft foam applicator pad (the softer black side of our special tri-foam applicators). Work on a 1 ft x 1 ft area at a time. This will ensure the product does not dry out before you work it fully into the finish. Using light to moderate pressure, rub briskly in a circular motion. Apply sufficient pressure initially, to remove microscopic dirt particles. Continue rubbing in polish until it disappears (gets absorbed ... more readily when using gentle pressure) and a high-gloss shine is visible. Wipe off any excess product (polish residue) carefully as you go, with a soft microfibre buffing cloth. Move to another section and repeat the application process, using a pea sized amount of polish for every square foot of surface area. Finish one panel or area entirely (apply product and buff off any excess) before moving on to the next section.

Machine Application: RMP or CDG Polish (non-abrasive) may also be applied by dual-action polisher, fitted with a foam polishing pad or soft foam finishing pad (recommended). Use small amounts of polish and work on a 2 ft x 2 ft area at a time. Allow the machine to operate under its own weight, without exerting much downward pressure. Work the polish into the finish at low to moderate speeds only (using slow overlapping passes), until it disappears and a high-gloss shine is visible. Wipe off any excess product (polish residue) carefully as you go, with a soft microfibre buffing cloth. Move to another section and repeat the process.

Please ensure the Re-Structure or Crystal Diamond Glaze products are applied to bare surfaces ... not on top of pre-existing sealant or wax based coatings.

When treating chrome, stainless steel, polished aluminium or other delicate surfaces, use a soft microfibre applicator pad or soft microfibre cloth instead. These are more suitable for polishing brightwork than foam. Apply the compound or polish using gentle motions only. Use a fresh, clean pad or cloth for each product; so there is no mix of compound and polish on the same applicator.

The RALG® molecular bonding process takes 24 hours to cure fully, after you have completed the last step. Try to avoid the sealant coating getting wet during this 24 hour period or for the first few hours (post application) at least.

Subsequent Applications - It is optional but advisable, to re-apply or top-up protection, every 12 to 18 months. Always wash and dry surfaces thoroughly before applying a renewal coating. Then, re-apply the sealant polish only (not compound), exactly as above. The polish can also be used as a one-step product for ongoing care and to fortify protection. Top up with additional coats periodically, to thicken surface protection. Please note, if using Micro Finishing Compound first, this will remove previous coat(s) of polish. Maintain the sealant coating with Re-Structure Mirasol sealant spray (optional). Wash (by hand) with a mild / pH balanced shampoo, one which does not contain wax.

Express Sealant Spray or RMP / CDG Polish (Sealant Coating) Booster. Protects from harmful UV rays, dirt and staining for up to six months. Excellent for use on paintwork, fibreglass, gel coat, glass, plexiglass, polycarbonate, plastic, vinyl, carbon fibre, varnished wood, brass, chrome, stainless steel and polished aluminium.

Mirasol = High gloss finish on glossy surfaces and natural or satin finish on low gloss surfaces.

Directions: For dirty surfaces, we recommend a thorough cleaning prior to the application of Mirasol.

Application: Shake well and use sparingly. Spray Mirasol directly to a clean surface. Work on a 2 ft x 2 ft area at a time. Spread out product with a soft microfibre pad. Using light pressure only, rub briskly in a circular motion. Follow-up by buffing to a high-gloss shine with a soft microfibre cloth. On porous plastic / vinyl surfaces, allow five minutes for Mirasol to penetrate, before wiping down.